Reid Select

Heavy Duty Telescopic Lid Stays are ideal for holding open lids, electric panel and inspection covers. They are suitable for heavy duty applications. The range offers left or right hand versions, and a choice of materials.Folding Lid Stays are ideal for holding open lids, electric panel and inspection covers. Can be used as left or right hand in a choice of materials.Folding Lid Stays are ideal for holding open lids, electric panel and inspection covers. The range offers left and right hand version in a choice of materials.

Lift-Off Hinge for Structural SystemsLift-Off Flag Hinges - Screw on are a two part rolled steel body with round end caps. Ideal for screw on frame for more industrial unitsMetal in-line Lift Off Hinges are easy lift off for flush mounted doors. They have a hinge rotation angle of 180 degree.Metal Offset Lift Off Hinges allows simple and quick door removal with an hinge rotation angle of 180 degree. Left and right hand available.Mini Metal In-Line Lift Off Hinges available for doors opening to the left. Metric uses M4 x 0.7 screws

Sometimes referred to as fluted knobs, lobed knobs with 10 lobes bridge a valuable gap between lobed knobs and knurled knobs by bringing wider grips than a typical knurled knob, while increasing the number of lobes over much wider gaps in knobs with fewer lobes.

They are ideal in setups where a "soft" grip is desired for hand cranking on equipment or workpieces.

Not sure whether a knob or handle is appropriate for your setup?

Check out our Engineer Guide to Knobs, Handles, and Handwheels to find the material and style of knob or handle that works best for your project’s specifications.

Locating pins are used for controlled, tight tolerances to increase accuracy in positioning workpieces on fixtures. Typically, two pins are needed to properly align the workpiece. We offer round pins that provide precise location in all directions, as well as relieved or diamond pins that provide clearance with less contact to prevent binding during loading and unloading. These can be used in many different applications including clamping tables, fixture plates, v-blocks and other common shop tools.

The most common types of fixture locating pins are: threaded locating pins, diamond locating pins, with bullet nose and pin liners.

Adjustable locating screws are used with locating pins to accurately position workpieces in jigs and fixtures.

These wire lock pins have a pin and cotter in one assembly. The wire loop is pulled over the pin end to lock it in place or remove it. Eliminates cotter pin loss. Headed shank formed of carbon steel. Retainer wire formed of MB spring wire. Zinc plated.Self-locking ring snaps down to hold them securely in place. Easy grip ring for quick removal. Pin is carbon steel, heat-treated to Rockwell RA 50-60. Ring is hot drawn spring steel with hardness of RC 47-48. Zinc plated.

Machine screw jacks are height adjustable and used to support elevated areas of a workpiece. We also carry ball-shaped and V-shaped screw jack pads.

Plain Grip Machine Strap Clamps reach over the work piece and hold it in place for maximum pressure. These clamps are available machined from solid bar stock or tempered steel with a varnished finish.

Our hex-hole, square-hole, and square-slotted machine tool sleeves can be used to connect rods for making boring bars, milling cutters, and tool holders.

These plates are grooved to be able to hold round parts as well. The plates are also notched for holding parts above base of vise. Smooth on back side. They are accurately machined, hardened and ground. Constructed of plates or channels with magnets sandwiched in between. Ideal for holding heavy parts. Effective holding against shear force.

With springs being such an integral part of power transmission applications, Reid Supply has about every kind of spring: compression springs, die springs, solid springs, drawbar springs, extension springs, torsion springs, etc.

Service and replace your springs on the go with our accessories that include music wire, snap buttons and spring winders.

Polycarbonate Moisture Separators filter contaminant water, dirt, and oil out of shop air using a centrifugal spinning action. The polycarbonate bowl includes an automatic float drain to expel built up liquids inside the bowl.

Mounted bearings and housings with rolling bearings support a rotating shaft, which can be bolted on a machine frame or any other substurcture. There is no need to precisely machine a bearing housing in a surrounding casing. This makes these solutions cost-efficient and easy to use, while providing full rolling bearing performance.

A large range of O-Rings and O-Ring kits are available for use in hydraulic and pneumatic applications for sealing purposes including ranges of both imperial and metric sizes

Pad eyes have a similar function as eye bolts and eye nuts, but unlike their counterparts, pad eyes are welded in place to create a permanent fastening point. While some types are suited for lifting applications, they can also be used as tie downs or attachment points to connect slings and rigging hardware. Made of forged carbon steel or stainless steel.

Piano hinges, also called continuous hinges, run the entire length of a door or lid. They provide more stability than traditional hinges, making them ideal for heavier doors and lids that require extra support.

Pin Chains are used to secure quick release pins to mating parts for easy accessibility and preventing loss of the pin. These stainless steel chains have two ID terminals, one at each end.

Pin Lanyards have a wide variety of uses for attaching pins and small parts. They come in a wide range of lengths, and have a choice of end attachements.

Pin Receptacles are designed for us on materials and in appications where the pins does not have anything to lock against. They provide a permanent and proper mating hole for all our quick release pins.

Pin rings are made from hard drawn wire steel and are zinc-plated. Stainless ones are type 316. Available in different diameters.

Flawless clarity for displays, food bins, and protective covers. Squeak-resistant nylon pin. Available in transparent, white, and black. Solvent cementable.

Pneumatics Mounts are well suited for applications that require higher deflection isolators and are easily leveled by adding or releasing air. This mount deflects shock loads and transfers the forces to the heavy duty outer wall, reducing vibration by up to 90%.

Pull handles are commonly used to open and close a variety of doors and drawers, including those on furniture, machines, and equipment. Options include one-piece handles or multiple-piece assemblies.

Double-sheave pulley blocks and wheels are used with cable or rope to lift or pull heavy loads. Designed for static applications, flat-block pulleys can be affixed to a wall, ceiling, or other firm, flat surface to ensure stability. Made from steel and other corrosion-resistant materials, they are suitable for indoor and outdoor use.