DESTACO Steel

Accessorize your actuators with floating joints, sensors, clevises and much more! These parts assist the actuators to meet application needs by enhancing alignment, mounting, sensing and attachment needs.

Base mounted plunger clamps Plunger have an extremely low height when in operation regardless of thehandle positionmaking these toggle clamps extremelt versatile when the working space is restricted.

Bolt Retainers are welded onto solid toggle clamp hold down bars after securing the spindle assembly with jam nuts. These bolt retainers are available for 1/2” – 5/8” spindle diameters.

Cone-Tip (Head?) Bonded Neoprene Spindle Assemblies provide an alternative choice to the spindle provided with the toggle clamp. The steel spindle is durable while the neoprene cone-tip minimizes marking with minimal clamping contact.

Flanged plunger clamper with push/pull action are part of this standard striaght line action toggle clamp

Flanged Washers are used with U-Bar clamps for securely latching applications on molds, doors, lids, access covers, drums, and containers. Flanged washers are available in durable steel or stainless steel.

Flat Head Spindle Assemblies provide an alternative choice to the spindle provided with the toggle clamp.

Hex Head Spindle Assemblies provide an alternative choice to the spindle provided with the toggle clamp. These assemblies have a stainless steel, steel, or nylon bolt that acts as the spindle cap and is supplied with two jam nuts.

General Purpose Single Acting Hydraulic Cylinders produce a linear force using pressurized hydraulic fluid to transfer power from fluid pressure to the piston and into the rod. These cylinders have a maximum operating pressure of 10,000 psi and included coupler.

J-Hook assemblies are ideal for latching applications on molds, doors, lids, access covers, drums, and containers. Made of steel or stainless steel.

Bolt-on Horizontal Latch Plates work with pull action latch clamps to provide a positive gripping power and lock the connection. These clamps are made of durable steel or stainless steel.

Sometimes referred to as fluted knobs, lobed knobs with 10 lobes bridge a valuable gap between lobed knobs and knurled knobs by bringing wider grips than a typical knurled knob, while increasing the number of lobes over much wider gaps in knobs with fewer lobes.

They are ideal in setups where a "soft" grip is desired for hand cranking on equipment or workpieces.

Not sure whether a knob or handle is appropriate for your setup?

Check out our Engineer Guide to Knobs, Handles, and Handwheels to find the material and style of knob or handle that works best for your project’s specifications.

Manual Push Pull Clamps have a single hole threaded mount to permit rotation in any direction. This design allows complete flexibility in the fixture in a compact design while securely holding materials in place during production.

Horizontal Manual Hold Down Clamps have a low height design, cushioned handle grip, and zinc plated components to resist corrosion. The handle and hold down bar move in opposite directions to provide secure holding capacity.

Manual Horizontal Hook & Latch Clamps operate on a horizontal plane allowing two faces to be fastened together on the same plane or at 90 degrees. These clamps have a low profile for applications having a height restriction.

Manuel Plier Clamps have a pivoting jaw to allow a large depth when clamping awkward profiles. The jaw spindle can be pre-set during repetitious action to achieve the optimum clamping distance and pressure.

Manual Swing Clamps are easy-to-use options for fixture building/testing, welding and assembly operations in the industrial, aerospace, and automotive markets. They provide quick swing-and-clamp movement for increased productivity. The new Manual Swing Clamps feature an enclosed cam track that can clamp and toggle-lock in the pull down closed position. They also feature a detent that holds the clamp in the open position in order to prevent unwanted movement.

Manual Through Hole Push Pull Clamps have a single hole threaded mount to permit rotation in any direction. This design allows complete flexibility in the fixture in a compact design while securely holding materials in place during production.

Manual Vertical Hold Down Clamps save valuable space without sacrificing holding capacity or clamp performance. A cushioned vinyl handle grip provides improved user comfort and all body and linkage components are zinc plated to resist corrosion.

Manual Vertical Hook & Latch Hold Down Clamps operate on a horizontal plane allowing two faces to be fastened together on the same plane or at 90 degrees. These clamps have a low profile for applications having a height restriction.

Plunger Spindle? Assemblies for Straight-Line Clamps automatically compensate for variations in part thicknesses. These assemblies are designed to be mounted to plunger clamps.

Pneumatic Block Hold Down Clamps provide clamping force from the top, wedging work pieces down against the work surface. Styles include automation power clamps, power rollers, and heavy duty clamps to best suit your application.

Pneumatic Cylindrical Hold Down Clamps provide activating force for over-center toggle clamps, applying pressure from the top. These cylinders are built to perform repetitive production operations with a magnetic ring for sensing capability.

Pneumatic Push Pull Clamps are used to apply pressure vertically in a straight-line action. Use clamps to wedge your project up against a rail or pair with another push pull clamp to apply force against each other in a vise-like application.

Plungers are a vital component of straight-line action clamps that pushes forward until contacting the work piece. Plungers are advanced and locked with the collet action by rotating the clamp locking lever.